How to cable management computer case

how to cable management computer case

Guide to Computer Cable Management

Sep 10,  · That is why cable management is becoming a necessity now. But worry not, in this article, we are going to be looking at how you can do cable management effectively, and efficiently. Choosing the Right Components. Cable management is not just the act of tidying up the cables on the back side of your case and calling it a day. Aug 31,  · With the cable management on both stations complete and I was very happy with the results. I realized that I was projecting my frustration with cable management from working inside PC cases, but when it comes to doing setup cable management it’s a lot easier because you have so much extra room to work with.

Cable management is my least favorite thing cimputer building computers, about setups, about managing my studio. What manafement as a project that I was kind of dreading turned out to be actually quite fun… I never thought I would say that about cable management. Many of the techniques we apply in dealing with cables inside a computer case apply to a desk as well.

Surprisingly, a lot of the accessories that I bought were not as helpful as I thought they would be. First to have these really awesome adhesive clamps that you can put literally anywhere on managment table, under, on the side, or even above. I also have these adhesive cable tie mounts, and they are awesome because you get to decide how large the cable tie you should use.

Of course, I have large and small cable ties computdr Velcro cable ties, which are super important. They always come in different mnagement and different colors too, and I will a hundred percent use them all in the long run. The last two items include this flexible Velcro channel that you can cut to size, and they are awesome because they can house both small and large cables.

Compuher first part of cable management — much like a case — is to remove anything that is unnecessary. Cabe in the managemetn of my desk, everything is such a mess. There is absolutely no organization in the cables and how they are channeled and where they are going. I actually ended up removing the plastic housing because removing cables from it is a complete pain, and I found a better way fase hide all my cables. One more item I forgot to mention is double sided tape, and this stuff is your friend, especially ensuring the power strip is in the right location below your desk, so you can hw things in.

One thing about mangaement desk is that it comes with a cable management hw that is right in the center, but there is also a metal frame right in the center of it so populating anything in that space is absolutely useless.

Eber has the same desk, but an earlier model, which did not have the support beams in the center, which means that you can put stuff there.

The next thing I wanted to do is secure all the cables one by one so they are properly organized, starting with my lighting cable. The only thing to keep in cabel with these adhesive clamp mounts is not to put too much tension via the cable, because the adhesive might not be as strong and it will peel over time.

Doing the rest of it really reminded me of doing cable management inside a computer case, but doing something with a desk is actually much more enjoyable because you have so much extra room.

Of course when it comes to lighting we have a power cable, we have a cable that routes both light towers, and we have a USB cable going into what causes posterior vitreous detachment PC, so I had to redo all the cable management. Follow the same type of technique and procedures to hide all these cables. After putting in a few hours everything was cleaned and organized.

Checking out the before and after shots I am very happy with how things turned out, a super clean under the table, super clean table top as well. Everything is just kind of collected and bunched up right behind the PC.

What is next? For this editing station I settled on my peripherals and the only thing I might swap out later might be the light towers or maybe the monitor, so that will be an easy job to do.

And then it was time to move on to my gaming station, and that actually was a bit more how to get a bursary for college because there is nothing underneath the desk and all the cables are completely exposed above and below. I use the same technique with the adhesive cable tie points and use a larger cable ties to bunch up some of the cables, so like the how to cable management computer case cable, the display cable, and the mouse and managemenh as well.

It is a more permanent solution, but if I do have to swap something out I will have to cut manqgement cable ties. The last thing I did was use a Velcro cable tie on the monitor stand majagement collect the cable, so they exit right down in the middle and they are not visible to you when you are sit on the computer. The end result above and below the desk is absolutely clean, as all the cables are actually on the edge of the desk and nothing is visible below.

With the cable management on both stations complete and I was very happy with the results. I will link all the products down below that you should check out if you are looking to cable manage your space as well. Let me know what you think of my first attempt at doing something proper with my setup. Dmitry August 30, Video Producer.

Mahagement Reviews.

Basics of Cable Management - Beginner's How-To Guide

Examine your case to see how many cable holes there are on your motherboard tray and where they're located. Measure the amount of space between the back of your motherboard . Oct 02,  · Cable management gives your computer the opportunity to run cooler and quieter, not to mention enhances its longevity, aesthetics and cleanliness. There were times when we didn’t bother about what was happening inside our computer cases, as long as everything was working wooustoday.com: Nikita Fedorov.

When you build your own gaming rig or have a computer with a side window so you can look inside and admire the amount of work and money that you have invested into your computer, why not make it look like it was build by professional? I built my own computer a few months ago and cable management was thought of before i ordered a single part. Common cable management techniques are cable shortening, lengthening, color changing, and sleeving. Such good cases ruined by ignorance and stupidity.

The 2 main things that determine how well you can hide all of your cords and wires are your computer case and your power supply. When choosing a case check for openings around where the motherboard will be placed, generally the more openings there are the better. Cooler Master cases are widely known for excellent cable management and for high air flow. Also the room behind the motherboard mounting plate the better because you can stuff more cords behind that plate.

Later I bought an optional side window for it from Cooler Masters website. Another reason I chose this particular case was the easy to remove front plate were I could hide yet more wires.

Keep in mind that a PSU can last you for your next build or maybe even the build after that given that cable standards don't change by then, so choose something that suits what you would like do with it in the future. I chose a Raidmax W PSU with detachable cords that can handle SLI and it wasn't as expensive as a Corsair Other small things you will need are: -zip ties [they are the standard but more permanent than other solutions] -twist locks -wire clips -twisty ties [like you use on produce bags in grocery store, they are easy to use over and over again] -spare wire of assorted colors -soldiering iron -soldier -heat shrink -sleeving -gorilla duct tape [looks good and hides cables that are behind motherboard mounting plate, plus it can hold cables in awkward places] -electrical tape -pliers -wire strippers You can also buy extensions but they get pricey fast.

First dissemble your case by taking off both side panels and the front panel [if you can, it helps to hide more things under it]. If you are building a computer from scratch or took you computer apart to redo it then the second step would be to put your PSU and motherboard into the case. If you have a lot of fans that need to be installed than it might be better to install those first but unlug the molex adapters, those will go in later. Find a place to hide all the fan molex plugs, I decided to attach them to an easy to remove 2.

Title says it all, start putting all the wires through the holes you want them in and plug them in. I had 3 fans that needed to reach to molex down in the HDD cage so i attached 3 of them together and ended up making my own molex adapter to save wire and space.

Unfortunately i ran out of heat shrink so used twist caps, when i have the cash ill do it it right. Unfortunately I didn't have my electrical box on me or I would include the lights in this instructable, I will add them later. This part is hard to put into words because everyone has there own idea of what the finished product should look like. Personally I like the natural flow look where everything looks even.

Ill admit that i got the general idea for this on someone else's instructable, but they used pieces of rubber which I cant afford so I used gorilla tape instead. If I had the dough i would like to get a really nice case like Zalman Fatility, Thermaltake Level 10GT, or I would convince Maingear to sell me one of their custom cases. I certainly wouldn't use duct tape for most of my build if I had the cash and I would definitely spend some time making my own cords and extensions.

What do the pros do differently? They paint the insides of their cases, use extensions and add a few flashy things that take the eyes off of cords like bright liquid cooling items, flashy reservoirs and a logo that really stands out.

I liked your walk-through. Showed people who didn't know how to do this the basics and a good jumping off point. Such good cases ruined by ignorance and stupidity". Everyone has their own learning curve That wasn't cool at all I love dem people who believe showing all the cables into a computer and calling it a day is cable management I have the exact same case, I built my pc in and my wiring is a mess inside. I actually just googled cable management, and clicked this link not knowing it was going to be the same case as mine.

This will help out a lot when I finally get around to situating my cables. A few things to note after making this Instructable and 3 years to collect better tools and skills , NEVER use twisty caps for electrical wires in a case, I was beyond broke when I made this Instructable because I just bought all the components, this could fry components, I recommend not changing any wire lengths unless you absolutely have to, if you do always soldier and sleeve.

The biggest mistake on my build was choosing performance over silence, you make a powerful little computer without the noise, all you have to do is buy components that are optimized to be quiet like Noctua fans with reducers I use Corsair fans with reducers , video cards that have non-reference coolers especially on AMD cards, Asus and MSI make really good heatsinks that are very quiet and keep it cool , All-in-one liquid coolers with fans in pull with fan shrouds.

Fan shrouds are not common, what they do is space the fan from the radiator which helps pull air through more parts of the radiator and makes it even more quiet by far the quietest setup I have found in my tests, the temperature results faired C better than a fan directly touching the radiator while being quite a bit quieter. I made my own fan shroud out of a dead fan, just cut out the fan and use the frame coupled with some new screws from the hardware store. I don't have a single part of the computer in this build in my new build.

My new build is a Mini-ITX small form factor gaming rig. If anyone is interested I'll post a few pics and the specs of the new build. Reply 6 years ago on Introduction. One thing, make sure you buy a motherboard that have a good design for cable management, coz there are a lot cheap motherboard with good performance but not compatible with cable management you want it.

I have built many computers since this and I am probably going to do a another cable management guide for small form factor gaming rigs that's what my current rig is. I am going to be taking all the cables out of my PC and re-doing my managment, Thank you for your guide and thats an awesome case in step 11! Great instructable! The center computer in your cases that disgust me section is water cooled.

Air flow is not a issue. It does look nasty, but the number one case to make for strict cable management is that it allows air to flow throughout the case as designed. My personal pet peeve is folks that take the side panel off for extended periods of time, especially those who think they are getting better cooling this way. Anyhow, great instructable, now I feel lazy.

Reply 9 years ago on Introduction. I have to admit, I do like to take my side panel off a lot, but only because I haven't put a window on my new case yet so I can't admire my work haha. I don't know how good the cable management is on that first case, but all the cable clutter around the HDD cage has to substantially decrease air flow especially since it seems like it omly has 2 fans.

Yes, no excuse for the pure sloth shown in your examples. I just trying to throw the guy a bone. Introduction: Guide to Computer Cable Management. By vanwazltoff Follow. More by the author:. SATA cords get in the way of the build so its best to put them in last.

Participated in the Hack It! Challenge View Contest. Did you make this project? Share it with us! I Made It! Prsnltrnr 4 years ago. Reply Upvote. Like I said I liked your presentation Otherwise, good job! EvolvedAwesome 6 years ago on Introduction. Sonofblaster 6 years ago on Step 9. I've gotten better than that now, I kind of had to when I got into small form factor building.

Very helpful! When I upgrade some of my parts I'll come back to this :P. Bartuss 6 years ago on Introduction. I was always wondering "what are those holes for? Thanks for putting me back on the good way! SugarCluster 6 years ago on Step According to this guide,my computer is already an abandoned rat nest : Plus,it's messed up and it's very low-end. One day when I upgrade my computer,I will do it according to this useful guide.

Thanks a lot!

4 Comment on post “How to cable management computer case”

Add a comment

Your email will not be published. Required fields are marked *